Find Research
Our World View
Industry Perspectives
Research Program
Parallax View Magazine
> stay tuned
View our collections of research around key subject areas:
>
>
>
>
ERP
>
>
>
>
>
>
>
SRM
>
>
WMS
 
 
Article
Impinj Monza R6 -- Another Significant Step in RFID's Progress

With the new Monza R6 chip, Impinj continues its relentless improvements to the performance and reliability of UHF RFID.


Full Article Below -
Untitled Document

I’m a Sensitive Chip

Impinj, the largest maker (by volume) of UHF RFID semiconductors, recently announced their next generation Monza R6 chips. With this chip, Impinj continues their unceasing improvements in RFID performance including read sensitivity of -22.1 dBm, enabling 25% greater read range than the existing tag chips, and tag encoding speed of 1.6 milliseconds for 32 bits. Beyond those performance improvements, Impinj has made a number of other innovations to improve reliability, yields, and performance.

Detecting the Defects

Impinj worked hard on delivering the best quality and consistency from what is really an amazingly inexpensive device. Though defect rates have been quite low, they become noticeable when a retailer is using tens of millions (or in some cases hundreds of millions) of tags every year. To increase the reliability, Impinj introduced what they refer to as “Integra” technology, which is a set of diagnostics that runs on the chip, testing memory and encoding reliability. A brief set of diagnostics is run upon each power-up of the chip, whereas a deeper set of diagnostics can be run on command. These diagnostics enable the chip to self-report failure, rather than relying solely on the testing done by inlay manufacturers and label converters. Not only can those tests miss some defects, but they cannot catch defects that occur later, after the assembly or encoding steps are completed.

Tune In and Don’t Drop Out

Another innovation is AutoTune. Normally tags are designed to work optimally for a specific application on a specific set of materials. If used on different materials, or other products are placed on top of or near the tag, or the moisture content in those materials near the tag increases, then the tag is detuned and performance goes down. Monza R6 has the ability to adjust its own internal impedance to one of five different levels. It very rapidly tries the different levels and selects the optimal one for the current environment. Basically it re-tunes itself to the current environment and object it is near. This means the same tag can be used on a wider array of product types1 while lessening the degradation caused by detuning.

Broadening Horizons

The other advantage of AutoTune is that it can adjust itself based on the frequency being used. Normally a so-called ‘broadband’ tag that is designed to work in all of the frequencies around the world compromises some performance to achieve the width of its band. As shown in Figure 1, the red line is a typical broadband tag, which gets less distance than the narrowband tags designed for a specific frequency/region.

Figure 1 - Comparison of Narrow-band vs. Typical Broadband Tag Performance

Impinj’s AutoTune is able to an extent get the best of both worlds. By adjusting the tuning, Monza R6 lifts up the performance at the lower and upper ends, so it can be closer to the ideal performance of the band-specific tag design. This enables a single tag to be used worldwide with better performance than traditional broadband tags.

Figure 2 - Sensitivity (Performance) Improvements Achieved Using AutoTune

Smoothing Out the Bumps = Increased Reliability

Monza R6 also introduced ‘Enduro’ technology to decrease failures and lower the applied tag cost. Traditionally RFID chips have four bumps for attaching the antenna. These bumps stick out and act as stress points that can actually cause cracking of the die (the RFID chip), especially during printing operations where a fair amount of pressure is applied on the tag. A crack may cause the tag to fail immediately and be marked as bad. But worse is when the crack is marginal and the tag tests out OK, but later it starts failing in operation.

Monza R6 addresses this by providing two antenna attachment surfaces that are much larger than the traditional bumps (see Figure 3). This improves yields in part because there are fewer cases of misalignment with the antenna connection leads. But more importantly, this design survives a much greater range of pressures and temperatures without cracking and failing. The most noticeable impact is when the tag goes through the printer, where Impinj said they are seeing big jumps in yields. Impinj is expecting an order of magnitude reduction in failures.

Traditional Die with
Small Antenna Attachment 'Bumps'
 
Monza R6 Die with Much Larger Antenna Attachment Area

Figure 3 - Comparison of Antenna Attachment Areas

Enduro also holds promise to drive down the cost of another component, the anisotropic conductive paste (ACP) used to glue the antenna to the chip. ACP is quite expensive because it contains gold-plated particles. With the big surface areas, tag manufacturers could use less amounts of ACP and yet get reliable connection with the antenna.

Small is Beautiful

There is a growing demand for smaller form factor tags that perform well, for example to tag jewelry and cosmetics (two categories the retailers increasingly would like to tag). All else being equal, smaller tags have shorter read distances. To achieve smaller form factor inlays, the inductor loop of the antenna needs to become smaller. To maintain performance, it requires higher input capacitance. But as you raise the input capacitance, variability in performance of small tags due to detuning effects becomes a limiting factor. With AutoTune, Enduro, and increased chip sensitivity, Impinj has been able to compensate for the detuning effects while increasing the input capacitance to enable smaller tag designs that still perform well. This is what is getting many of their customers excited.

A chip that is more sensitive, more reliable, enables designs to work across a broader range of materials and frequencies, and enables smaller tag designs with good performance – all at the same price point as previous generation – what’s not to like about Monza R6? The R6 is one more example of why Impinj continues to lead the UHF RFID market.

_________________________

More reading on RFID: http://www.chainlinkresearch.com/rfid/index.cfm

____________________________________________

1 There are limits to the amount of tuning that can be done. You could not design one tag to work well on everything from metals to liquids to fabric—that still requires multiple tag designs. But AutoTune increases the range of types of products and materials that a single tag design will work well on. -- Return to article text above

To view other articles from this issue of the brief, click here.




MarketViz powered.